Backflow test kit calibration in South Carolina
A tester renewing a South Carolina card uses their own differential pressure gauge. R.61-58.7(F)(8)(a) says that gauge has to be accurate within 2 percent of full scale or plus or minus 0.3 PSID. The 2025 SCDES study guide adds a separate requirement that gauges be certified or calibrated annually. This page is those two requirements. It does not name a calibration shop, and it does not list a price.
Sources checked October 23, 2026.
A customer with a test notice hires a General Tester. The customer does not send a gauge out for calibration. What is backflow testing is the annual-test rule. County lists from the July 9, 2026 SCDES report start at Greenville County. What the state requires the kit to be, including the three-valve and five-valve procedures, is on Backflow test kits.
The accuracy line at the three-year renewal
R.61-58.7(F)(8)(a) says each certified tester’s license expires three years from the date of issue. To renew it for three more years, the tester comes before a designated person approved by the Department, successfully completes a written examination with a passing score of 70 percent, and performs the prescribed test on an approved reduced pressure principle assembly, a double check valve assembly, and a pressure vacuum breaker. Those tests use the tester’s own differential pressure gauge.
The same subsection says the gauge must be accurate within 2 percent of full scale or plus or minus 0.3 pounds per square inch differential (PSID). The SCDES program page states that renewal check in its own words: within 2 percent of full gauge scale or ±0.3 psi differential. The wet lab on that page is the same three assemblies. How the four tester cards differ, and how the course and the three-year renewal are scheduled, is on General vs Limited.
Full scale means the full-scale range of the gauge used for the test. The regulation prints both tolerances and joins them with “or.” It does not print a full-scale range to substitute for the range on the gauge, and it does not say which tolerance controls when the two numbers differ.
The certified-tester definition in the same regulation says a General Tester has personal possession of, or the employer owns, a backflow prevention assembly test kit. Section (8)(a) names the gauge used at renewal as the tester’s own. Keep both sentences. The regulation does not add a third sentence that chooses between them.
When the gauge has to be calibrated or repaired
Section (8)(a) says any gauge found to be inaccurate or malfunctioning has to be calibrated or repaired as needed to bring it into compliance before certification will be renewed.
Section (8)(b) is about the test. An applicant who fails to properly perform the prescribed tests has the certification revoked immediately and has to successfully complete the state-sponsored backflow prevention training and certification course to be re-certified. A gauge the designated person finds inaccurate is the case section (8)(a) sends to calibration or repair before renewal.
The annual line is in the study guide
The cover letter in the 2025 recertification study guide lists updates to the certification program. The first item says test equipment and gauges are required to be certified or calibrated annually. The gauges section of the same guide repeats that gauges are required to be certified or calibrated annually. The guide prints that phrase with a slash, “certified/calibrated.”
Section (8)(a) measures the license in three-year terms and places the accuracy line on the gauge used at renewal. The study guide is the SCDES document that uses the word annually for the gauge.
The guide does not name a calibration laboratory. It does not print a fee for that annual check. It does not describe the procedure used to certify or calibrate the gauge, and it does not define “certified” past the slash with “calibrated.”
The gauges section also says to treat gauges as instruments, to snug needle valves rather than overtighten them, to open every valve and shake the hoses out at the end of a test, and to store the gauge with the valves open, in a safe and secure manner. Those sentences sit next to the annual line. They are handling instructions in the study guide. They are not a calibration method.
The station list schedules the exam
The study guide’s station pages list current re-certification stations. The guide says the tester contacts one of those stations to schedule the recertification exam, and that the proctor provides the dates, costs, and locations of the next scheduled exam. The program page names the same choice: renew at a center listed in the study guide, or repeat the certification workshop. The guide does not call those stations calibration laboratories, and it does not print a dollar amount. This page does not add one.
Questions on the cover letter go to Steve Fox, Cross-Connection Control and Backflow Prevention, Bureau of Water, at (803) 898-4426 or Steve.Fox@des.sc.gov. The same name and phone are on the program page.
The tester certification course overview describes the four-day certification class, the written exam, and the hands-on test of the three assemblies. It says the card is valid for three years from initial certification or recertification. It does not describe a gauge-calibration procedure.
What four Upstate manuals say about the gauge
Anderson’s September 2008 policy defines a differential gauge as an approved and calibrated gauge. The calibration sentence says the tolerance is plus or minus 2 percent, equal to 0.3 psid. That wording treats the two numbers as one tolerance. R.61-58.7(F)(8)(a) states them with “or.” How Anderson handles notices is on Anderson, Pickens, and Oconee.
Seneca Light & Water’s manual, revised October 2021, suspends a certified tester from testing when the gauge is out of the tolerance in the gauge manufacturer’s specifications. The tester may continue after the gauge is replaced or repaired and calibrated to that specification. That paragraph does not print the state’s 2 percent line. How Seneca keeps its permitted list is on Seneca Light & Water.
Greenville Water’s cross-connection manual defines a certified tester as a person who completed the training and certification seminar and who has an up-to-date tester certification card and approved testing equipment. The definition still uses the letters SCDHEC. The study guide’s cover letter says SC DHEC separated into two agencies on July 1, 2024, and that the agency is now the South Carolina Department of Environmental Services. The text of the Greenville manual, read October 23, 2026, does not state a gauge-calibration tolerance. Filing for that utility is on Greenville Water.
Spartanburg Water’s manual, revised June 4, 2026, defines a certified tester as any person possessing a current SCDES tester certification and approved testing equipment. The text of that manual, read October 23, 2026, does not state a gauge-calibration tolerance. That utility’s notice rules are on Spartanburg Water.
A utility notice that names a laboratory, a sticker, or a due date for the gauge controls that account. These four manuals are the ones read for this page. For a utility that is not one of the four, check that utility’s notice.
What the state sample form records
SCDES’s sample test form has a line for the gauge serial number. It has lines for test type, testing firm, tester name, and certification number. It has no line for a calibration date. The form says many jurisdictions require their own form. A field-by-field reading of the utility forms already on this site is on How to read your notice.
A General Tester who wants a listing started from the state report uses For testers. Official links are on Resources.
Backflow test kits General vs Limited
Sources checked October 23, 2026: R.61-58 on des.sc.gov; the SCDES Cross Connection Control program page; the 2025 recertification study guide; the SCDES tester-certification course overview; the SCDES sample test form; Greenville Water’s cross-connection manual at CCC-Manual-20251110.pdf; Spartanburg Water’s manual revised June 4, 2026; Anderson Electric City’s September 2008 cross-connection policy; Seneca Light & Water’s backflow manual revised October 2021.